Nycz Posted July 3 Member ID: 22476 Group: ** Registered Users Followers: 11 Topic Count: 31 Topics Per Day: 0.01 Content Count: 193 Content Per Day: 0.05 Reputation: 84 Achievement Points: 1396 Solved Content: 0 Days Won: 0 Joined: 03/24/15 Status: Offline Last Seen: 14 hours ago Birthday: 06/17/1993 Device: Windows Posted July 3 NZXT H6 Flow with Kraken 360 AIO Kept the xfx rx 7700xt gpu. Needed a better case and cooling more. Striker, Hoth and major-mark63 3
++ COD4 Admin Totty Posted July 4 Member ID: 30308 Group: ++ COD4 Admin Followers: 10 Topic Count: 39 Topics Per Day: 0.03 Content Count: 932 Content Per Day: 0.81 Reputation: 949 Achievement Points: 8449 Solved Content: 0 Days Won: 10 Joined: 07/02/22 Status: Offline Last Seen: 7 hours ago Birthday: 08/28/1973 Device: Linux ++ COD4 Admin Posted July 4 Looks nice, kudos to you for getting up at 06.22 to take a pic Striker 1 Awards
Nycz Posted July 4 Member ID: 22476 Group: ** Registered Users Followers: 11 Topic Count: 31 Topics Per Day: 0.01 Content Count: 193 Content Per Day: 0.05 Reputation: 84 Achievement Points: 1396 Solved Content: 0 Days Won: 0 Joined: 03/24/15 Status: Offline Last Seen: 14 hours ago Birthday: 06/17/1993 Device: Windows Author Posted July 4 Thanks. It was 6:22pm though. Lol
KaptCrunch Posted July 5 Member ID: 389 Group: *** Clan Members Followers: 48 Topic Count: 401 Topics Per Day: 0.07 Content Count: 5445 Content Per Day: 0.94 Reputation: 4676 Achievement Points: 43521 Solved Content: 0 Days Won: 80 Joined: 09/14/09 Status: Offline Last Seen: 2 hours ago Birthday: 01/01/1970 Device: Windows Posted July 5 (edited) very nice case i hate tell that how rad is placed is big air trap when coolant level drops leaves no heat transfer from less contact to tubes. best move the rad with fans blowing outward of the front corner of case with bungs up and move 3 fans to the top of case bllowing inward also turn cpu 180° so that can be self priming and 2 bottom fans blow inwards. oh forget to say get a fan cotrollier that has 4 channels and min, 1 amp per channel note your AIO fan is 12V DC, 0.23A (2.76W) = x3 .23A = .69 Amps gang them parrelle, do the same with 3 upper now formally front corner and 2 lower fans case fans just check watts rating per fan convert to amps, stay within ! Amp by 10%. also the rear fan blow inward after all done use a inferad temputer gun an check heat pattern and adjust fan speeds Edited July 5 by KaptCrunch adding fan controllier Hoth 1 Awards
KaptCrunch Posted July 5 Member ID: 389 Group: *** Clan Members Followers: 48 Topic Count: 401 Topics Per Day: 0.07 Content Count: 5445 Content Per Day: 0.94 Reputation: 4676 Achievement Points: 43521 Solved Content: 0 Days Won: 80 Joined: 09/14/09 Status: Offline Last Seen: 2 hours ago Birthday: 01/01/1970 Device: Windows Posted July 5 i would add a water reservoir after warranty runs out Note: not made of Acrylic material for will crack with heat cycles or any alchol like the typoon3 PC water reservoir did for they used my design after i set them up for notice they were using my ideals without payment or acknowledgement, jokes on them Awards
Nycz Posted July 5 Member ID: 22476 Group: ** Registered Users Followers: 11 Topic Count: 31 Topics Per Day: 0.01 Content Count: 193 Content Per Day: 0.05 Reputation: 84 Achievement Points: 1396 Solved Content: 0 Days Won: 0 Joined: 03/24/15 Status: Offline Last Seen: 14 hours ago Birthday: 06/17/1993 Device: Windows Author Posted July 5 its a AIO, no water cooler plus everything you just said is opposite of what is online and has been tested for years. Rear and top fans always blow out with front/ bottom in. the only real possible change but not with this case is moving the aio to front to get barely any cooler air in with just 3 fans top still going out.
Recommended Posts