RogueKill Posted October 25, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Posted October 25, 2010 Any one needing help-- I have been a tech for 25 years---master ASE/CHRYSLER AND GM. Owned own shop for ten years. Also did online diagnostics for awhile previously. More than happy to help!! Please include info and good description of the problem. 1. make/ model/ year 2.miles and engine size 3.description of problem and if anything has been done to it (the more info, the easier the diagnostic and more accurate) Awards
ROCKAPE Posted October 25, 2010 Member ID: 4 Group: ++++ Senior Admin Followers: 172 Topic Count: 1107 Topics Per Day: 0.19 Content Count: 5185 Content Per Day: 0.91 Reputation: 3128 Achievement Points: 43910 Solved Content: 0 Days Won: 15 Joined: 09/01/09 Status: Offline Last Seen: Tuesday at 06:47 PM Birthday: 08/16/1967 Device: Windows Posted October 25, 2010 RogueKill thats a great offer of help to people many thanks. Awards
BUDMAN Posted October 25, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 25, 2010 Been a Tech since 1980 you do the math...hehehe working for G.M. (chevy) now and have been for years as roguekill I also am ase master tech and L1 Advanced (driveability) feel free to contact me via pm or email BUDMAN Awards
RogueKill Posted October 25, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 25, 2010 Thanks Rock, lotta good people here. I have been blessed in a lot of ways---just tryin to pass it on. I just want to add also that if anyone would like a second opinion on repair estimate $$ before they get them done I can do that also. Just for peace of mind that they are not overpaying for repairs. It's tough out there right now and every dollar counts! Awards
BUDMAN Posted October 25, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 25, 2010 RogueKill I just want to add also that if anyone would like a second opinion on repair estimate $$ before they get them done I can do that also. Just for peace of mind that they are not overpaying for repairs. It's tough out there right now and every dollar counts! Bump ...what he said Awards
RogueKill Posted October 25, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 25, 2010 COOL BUD! When I first opened my shop here in Colorado thats what I did--emissions, driveability repair. I was going around to different shops at night and fixing the cars they couldn't figure out, then one day I fixed the right guy's car and he backed me financially to open my own. I was like the first driveability shop in co. springs --we wore labcoats. and everything lol Awards
BUDMAN Posted October 25, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 25, 2010 Very Cool maybe between us we can help all the IDIOTS in here ...lol Awards
Dark Asylumn Posted October 25, 2010 Member ID: 809 Group: *** Clan Members Followers: 41 Topic Count: 252 Topics Per Day: 0.04 Content Count: 2840 Content Per Day: 0.50 Reputation: 1032 Achievement Points: 20424 Solved Content: 0 Days Won: 1 Joined: 11/29/09 Status: Offline Last Seen: 8 hours ago Birthday: 06/25/1979 Device: Windows Posted October 25, 2010 i lived in the springs for a few years cool Awards
RogueKill Posted October 25, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 25, 2010 Really? When and where DARK? Who was Jimmy Goad--he was born just 5 days after me. Awards
Dark Asylumn Posted October 25, 2010 Member ID: 809 Group: *** Clan Members Followers: 41 Topic Count: 252 Topics Per Day: 0.04 Content Count: 2840 Content Per Day: 0.50 Reputation: 1032 Achievement Points: 20424 Solved Content: 0 Days Won: 1 Joined: 11/29/09 Status: Offline Last Seen: 8 hours ago Birthday: 06/25/1979 Device: Windows Posted October 25, 2010 i lived on rockrimmon blvd on rimview dr in the apts there between the plaza and the interstate. in 2001-03, jimmy was a dear friend of mine here in ky Awards
RogueKill Posted October 25, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 25, 2010 COOL COOL- I have a little shop now right south of there--- that conoco station on the west side of I-25 and fillmore. I got laid off ( well I actually quit due to lack of hours) in Feb. from COLORADO SPRINGS DODGE-USED TO BE CARLIN DODGE) I used to live in Henderson KY. Awards
1lost1 Posted October 26, 2010 Member ID: 938 Group: ***- Inactive Clan Members Followers: 25 Topic Count: 19 Topics Per Day: 0.00 Content Count: 602 Content Per Day: 0.11 Reputation: 339 Achievement Points: 4774 Solved Content: 0 Days Won: 1 Joined: 12/28/09 Status: Offline Last Seen: March 26 Birthday: 08/28/1972 Device: iPhone Posted October 26, 2010 Ok heres one.. For the Heep 04 TJ having trouble with toe in I belive (well thats what the tire shop says) Question can I do a close alignment myself ? Thanks lost Awards
RogueKill Posted October 26, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 26, 2010 Question: Why do they say that? Tire wear? pulling/drifting? Do you have stock tires/lifted? You can set toe yourself with a tape measure-kinda crude but sounds like you have another issue- it shouldn't keep losing toe adjust. If you could give me a little more info. -------------------Answering those ???'s would help alot. There is a TSB for offset balljoints TSB 02-001-02- but that would affect caster/camber, also the factory steering stabilizer shock on those is a piece of shit- we always replace them at Jeep with a heavy duty Rancho(They are actually less expensive than the junk one you get at Jeep) Give me some more info and I will check back when I get to work Awards
SGTDANKO Posted October 26, 2010 Member ID: 3214 Group: **- Inactive Registered Users Followers: 27 Topic Count: 206 Topics Per Day: 0.04 Content Count: 2362 Content Per Day: 0.49 Reputation: 50 Achievement Points: 14004 Solved Content: 0 Days Won: 0 Joined: 02/21/12 Status: Offline Last Seen: July 4, 2015 Birthday: 06/23/1981 Posted October 26, 2010 ok i got one for you i have a 04 gmc yukon denali 6.0l in the shop right now came in with the code p0161 o2 heater performance prob b2s2 i replaced the sensor as the resistance on that sensor did not match the other three car came back with the same code so now i went into testing the curcits ign 1 supliies the 12 volts to both bank 2 sensors and comuter supliies the ground both curcits are fine i have done the o2 heater test with a scan toll and its working it is pulsing the heater off and on once per sec so im stummped new sensor and cuircits are fine im going to continue on it today ill let you know if i find prob and ill check forum to see if you have a fix thanks danko
RogueKill Posted October 26, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 26, 2010 That might be a good one for bud, but can you swap the new 02 with one of the other 02's just to eliminate the new sensor as being bad out of the box?=i have seen that.check your resistance on both the heater low circuit and the voltage circuit between there and pcm--should be no more than 3 ohms on either. If both those check out you could be looking at a pcm failure. I dont see any bulletins but BUDMAN works at chevy and probably has access to any NEW software issues--they post them seperately so only gm techs have access and i dont have that anymore. Awards
Nutcutter Posted October 26, 2010 Member ID: 1540 Group: **- Inactive Registered Users Followers: 13 Topic Count: 40 Topics Per Day: 0.01 Content Count: 856 Content Per Day: 0.16 Reputation: 100 Achievement Points: 4812 Solved Content: 0 Days Won: 0 Joined: 06/28/10 Status: Offline Last Seen: May 6, 2017 Birthday: 09/20/1969 Posted October 26, 2010 OK I got a 2000 Blazer LT 6 cyl that about 75% of the time has low power when its in the first cold start loop. And it does not seem to matter if its warmed up or cold. Just for about the first 1 1/2 mins after you start it. I have a scanner on my laptop and cannot see anything out of the ordinary. No codes at all, did Replace an O2 sensor about 6 months ago, and fuel pump a bit before that, but it was doing it before that. Had a tune-up etc. no difference. Im stumped!
RogueKill Posted October 26, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 26, 2010 That could be a tough one NUT, again maybe another good one for Budman. But those had A LOT of problems with the injector poppets plugging up,leaking. GM has an upper engine cleaner that they spray in the intake and let set,as well as cleaning the poppets directly like the fuel inj. svc you normally get. Sometimes they can leak--also I have seen the fuel pressure regulator leak(it is internal in the intake manifold)Do you see any black smoke until it starts re-gaining power? 1 way to check is to open the throttle plates and have someone turn key-on-engine off while you watch down inside throttle body and see if you see fuel leaking anywhere inside. Almost bet it is one or the other. That "spider" (as we call it) is a piece of crap.I think they might even have a conversion kit to make it MFI instead of SFI.but prob. expensive. Might get you a can of that upper engine clean from gm and try running a can of BG44K through the tank, especially if you dont see fuel leak in manifold. Awards
BUDMAN Posted October 26, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 26, 2010 First of all Mr Danko what are the amp reading on the scan tool ? 2nd does this truck have remote start ? (after market). Is this an aftermarket o2 sensor or G.M. and the ignition should be off for 10 hours for proper resistance test of the heater circuit. And always use dielectric grease on all connectors....... check connector at ecm/pcm and apply grease. Test these circuits the ho2s hearter low control circuit and the ingintion 1 voltage circuit should be 3 oms feel free to hit me up anytime. Oh by the way how often does this occur................................. Awards
BUDMAN Posted October 26, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 26, 2010 Ok nut i need a lilttle info b4 i can help.What is the short term and long term fuel trim numbers would help,and make sure you are in closed loop (hot after drive at idle) I am thinking the cpi unit maybe taking a crap... but need more info and make sure your gas does not have to much alcohol/contaminats in fuel. hit me up anytime BUDMAN Awards
RogueKill Posted October 26, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 26, 2010 BUDMAN Ok nut i need a lilttle info b4 i can help.What is the short term and long term fuel trim numbers would help,and make sure you are in closed loop (hot after drive at idle) I am thinking the cpi unit maybe taking a crap... but need more info and make sure your gas does not have to much alcohol/contaminats in fuel. hit me up anytime BUDMAN Hey Budman,I havent been with gm since 04,but I got to noticing alot of bulletins about excessive alcohol content. Are they having alot of problems with that? Awards
BUDMAN Posted October 26, 2010 Member ID: 800 Group: *** Clan Members Followers: 152 Topic Count: 139 Topics Per Day: 0.02 Content Count: 7101 Content Per Day: 1.26 Reputation: 4639 Achievement Points: 60396 Solved Content: 0 Days Won: 6 Joined: 11/27/09 Status: Offline Last Seen: 1 hour ago Birthday: 05/29/1957 Device: Windows Posted October 26, 2010 Yes alot of trucks/cars have e85 option which has a sensor that detechs how much and pcm/vcm adjust as needed...... well that can go screwy and somtimes needs to be reset if not will cause lean and or rich conditions that make no sense because computor is doing what it is told too. what a lot of peeps dont know is that 1 gal of gas goes much further than 1 gal of e85.... and hear in fl methenal is going up to 15 % instead of the 10% we are use to and is going to affect fuel milage something you may need to know 1 day one.ThingI get alot of because of peeps coming down south dont understand there are different mix for winter and summer fuels,and causing driveability concerns for sure. note the hell with typing shit hit me up on x fire ..lol ok anytime Awards
SGTDANKO Posted October 27, 2010 Member ID: 3214 Group: **- Inactive Registered Users Followers: 27 Topic Count: 206 Topics Per Day: 0.04 Content Count: 2362 Content Per Day: 0.49 Reputation: 50 Achievement Points: 14004 Solved Content: 0 Days Won: 0 Joined: 02/21/12 Status: Offline Last Seen: July 4, 2015 Birthday: 06/23/1981 Posted October 27, 2010 alright guys thanks for the responses last night before i left i swapped both b2 sensors and when i came in this mornning and fired it up sure enough the prob followed so prob solved it was bad out of box it threw a pending code for p0141 b1 instead of b2 lmao stupid defective parts thanks again guys
SGTDANKO Posted October 27, 2010 Member ID: 3214 Group: **- Inactive Registered Users Followers: 27 Topic Count: 206 Topics Per Day: 0.04 Content Count: 2362 Content Per Day: 0.49 Reputation: 50 Achievement Points: 14004 Solved Content: 0 Days Won: 0 Joined: 02/21/12 Status: Offline Last Seen: July 4, 2015 Birthday: 06/23/1981 Posted October 27, 2010 Nutcutter OK I got a 2000 Blazer LT 6 cyl that about 75% of the time has low power when its in the first cold start loop. And it does not seem to matter if its warmed up or cold. Just for about the first 1 1/2 mins after you start it. I have a scanner on my laptop and cannot see anything out of the ordinary. No codes at all, did Replace an O2 sensor about 6 months ago, and fuel pump a bit before that, but it was doing it before that. Had a tune-up etc. no difference. Im stumped! mabye a cloged catalatic converter try pulling an upstream o2 sensore then go for a drive and see if she has any pwr if it is the same that rules out exhaust ive also seen a pcv valve cause low power make sure its not frozen and air only goes one way srry not much help unless im hands on danko
RogueKill Posted October 27, 2010 Member ID: 1588 Group: ***- Inactive Clan Members Followers: 7 Topic Count: 84 Topics Per Day: 0.02 Content Count: 904 Content Per Day: 0.17 Reputation: 139 Achievement Points: 5532 Solved Content: 0 Days Won: 3 Joined: 07/19/10 Status: Offline Last Seen: August 26, 2024 Birthday: 08/25/1966 Device: Windows Author Posted October 27, 2010 sgtdanko>xi< alright guys thanks for the responses last night before i left i swapped both b2 sensors and when i came in this mornning and fired it up sure enough the prob followed so prob solved it was bad out of box it threw a pending code for p0141 b1 instead of b2 lmao stupid defective parts thanks again guys WOOOOOOOOOOHOOO!!! Our first Diagnostic!! Cool beans Sarge, glad we could help. Awards
Malificent Posted October 27, 2010 Member ID: 38 Group: **- Inactive Registered Users Followers: 0 Topic Count: 92 Topics Per Day: 0.02 Content Count: 1255 Content Per Day: 0.22 Reputation: 3 Achievement Points: 7228 Solved Content: 0 Days Won: 0 Joined: 09/01/09 Status: Offline Last Seen: Never Birthday: 11/06/1971 Posted October 27, 2010 Well RogueKill... Find me my oxygen sensors for an 08 Ford Focus....a woodchuck chewed through the cables and soldering isn't an option. 2 sensors btw....
Recommended Posts